铝合金非等界面复合板的轧制可行性分析
PDF下载 (371)谭 威,邵熠羽,李 贺,彭文飞.铝合金非等界面复合板的轧制可行性分析[J].宁波大学学报(理工版),2022,35(4):29-33.DOI:
TAN Wei,SHAO Yiyu,LI He,PENG Wenfei.Analysis on rolling of aluminum alloy unequal interface composite plate[J].Journal of Ningbo University(Natural Science & Engineering Edition),2022,35(4):29-33.DOI:
| Title: | Analysis on rolling of aluminum alloy unequal interface composite plate |
| 作者: | 谭 威, 邵熠羽, 李 贺, 彭文飞 |
| Author(s): | TAN Wei, SHAO Yiyu, LI He, PENG Wenfei |
| 关键词: | 非等界面; 复合轧制; 铝合金; 热轧实验 |
| Keywords: | unequal interface; rolling-bonding; aluminum alloy; hot rolling experiment |
| 分类号: | TG335.81 |
| 文献标识码: | A |
| 摘要: | 基于ANSYS LS/DYNA仿真软件, 探究不同压下率、轧制温度对铝合金非等界面复合板的影响规律, 并通过热轧实验对非等界面复合加以验证. 结果表明: 随着压下率的增大, 垂直压应力也随之增大, 同时垂直压应力呈现流道附近最大, 两端边部最小; 轧制过程中的上下板垂直应力变化趋势一致, 通过最大垂直应力与变形抗力比值分析得出边部区域复合较为困难. 热轧温度在400℃、430℃时, 边部界面在压下率为30%时就能完全复合, 此温度利于复合板复合; 热轧温度在460℃时, 边部界面在压下率为50%时才能完全复合, 不利于复合. 选用仿真优化参数组, 通过实验对比取样发现, 在微观下看到明显的复合界面与非复合界面的交界处, 说明非等界面复合板成功复合, 这为其他金属非等界面复合判断分析提供了理论基础. |
| Abstract: | Based on ANSYS LS/DYNA simulation software, the influence of different reduction rates and rolling temperatures on the non-uniform interface composite plate of aluminum alloy was explored, and the non-uniform interface composite was verified by hot rolling experiment. The results show that with the increase of the reduction rate, the vertical compressive stress also increases, and the vertical compressive stress is the largest near the flow channel and the smallest at both ends. In the rolling process, the change trend of vertical stress of upper and lower plates is consistent. Through the analysis of the maximum vertical stress and deformation resistance ratio, it is difficult to compound the edge area. When the hot rolling temperature is 400℃ and 430℃, the edge interface can be completely composited when the reduction rate is 30%, which is conducive to the composite plate; when the hot rolling temperature is 460℃, the edge interface can be completely composited when the reduction rate is 50%, which is not conducive to composite. The simulation optimization parameter group was selected. Through the comparative sampling of the test, the obvious interface between the composite interface and the non-composite interface can be found at the micro level. It indicates that the non-uniform interface composite plate was successfully composited, which provided a theoretical basis for the judgment and analysis of the non-uniform interface composite of other metals. |
| 参考文献 /References: | [1] 方坤, 朱勇, 宋奎晶, 等. 集成固相焊接方法在液冷板制造中的应用[J]. 电子机械工程, 2018, 34(1):43-45; 64. [2] 黄馗, 王文. 动力电池组液冷散热系统[J]. 电源技术, 2019, 43(3):415-419. [3] 李杰, 黄健康, 靳全胜. 铝/钢异种金属熔钎焊方法研究现状[J]. 电焊机, 2018, 48(1):109-114. [4] 金建新. 铝合金水冷板的铸造工艺研究[J]. 特种铸造及有色合金, 2002, 22(2):47-49. [5] 喻海良, 赵宪明, 刘相华. 板带精轧过程轧制力的三维弹塑性有限元分析[J]. 钢铁研究, 2005, 33(1):14-16. [6] 孙铁铠, 刘恩来. 用弹塑性有限元模拟双金属复合板轧制[J]. 钢铁研究学报, 2002, 14(5):26-29. [7] Saito Y, Utsunomiya H, Tsuji N, et al. Accumulative roll-bonding of 1100 aluminum[J]. Journal of the Japan Institute of Metals and Materials, 1999, 63(6):790-795. [8] Saito Y, Utsunomiya H, Tsuji N, et al. Novel ultra-high straining process for bulk materials — development of the accumulative roll-bonding (ARB) process[J]. Acta Materialia, 1999, 47(2):579-583. [9] Pirgazi H, Akbarzadeh A, Petrov R, et al. Microstructure evolution and mechanical properties of AA1100 aluminum sheet processed by accumulative roll bonding[J]. Materials Science and Engineering: A, 2008, 497(1/2):132-138. [10] Du Q L, Li C, Cui X H, et al. Fabrication of ultrajine-grained AA1060 sheets via accumulative roll bonding with subsequent cryorolling[J]. Transactions of Nonferrous Metals Society of China, 2021, 31(11):3370-3379. [11] Wang Z J, Ma M, Qiu Z X, et al. Microstructure, texture and mechanical properties of AA1060 aluminum alloy processed by cryogenic accumulative roll bonding[J]. Materials Characterization, 2018, 139:269-278. [12] Su L H, Lu C, Gazder A A, et al. Shear texture gradient in AA6061 aluminum alloy processed by accumulative roll bonding with high roll roughness[J]. Journal of Alloys and Compounds, 2014, 594:12-22. [13] 焦少阳, 董建新, 张麦仓, 等. 双金属热轧复合的界面结合影响因素及结合机理[J]. 材料导报, 2009, 23(1):59-62. [14] 张东来, 高建和, 张进. 6063铝合金本构模型及其有限元仿真[J]. 机械工程与自动化, 2014(6):118-120. [15] Li P, Li F G, Cao J, et al. Constitutive equations of 1060 pure aluminum based on modified double multiple nonlinear regression model[J]. Transactions of Nonferrous Metals Society of China, 2016, 26(4):1079-1095. [16] 喻海良. 金属板带塑性成形有限元分析[M]. 北京: 科学出版社, 2018. |
| 备注/Memo: | 收稿日期: 2022－02－09. 宁波大学学报（理工版）网址: http://journallg.nbu.edu.cn/基金项目: 国家自然科学基金（52075272）; 浙江省自然科学基金（LY18E050006）; 宁波市科技计划（2018B10004, 2019B10100）; 宁波市自然科学基金（2017A610088）.第一作者: 谭威（1994－）, 男, 湖南岳阳人, 在读硕士研究生, 主要研究方向: 金属塑性加工工艺与装备. E-mail: 392272986@qq.com*通信作者: 彭文飞（1983－）, 男, 湖北天门人, 副教授, 主要研究方向: 金属塑性加工工艺与装备. E-mail: pengwenfei@nbu.edu.cn 宁波大学学报（理工版）网址：http://journallg.nbu.edu.cn/ |
