采用改进PI迟滞模型的压电微夹钳前馈控制
PDF下载 (34625)蔡永根,崔玉国*,赵余杰,刘尔春,刘 康,薛 飞.采用改进PI迟滞模型的压电微夹钳前馈控制[J].宁波大学学报(理工版),2017,30(6):53-58.DOI:
CAI Yong-gen,CUI Yu-guo*,ZHAO Yu-jie,LIU Er-chun,LIU Kang,XUE Fei.Feedforward control of a piezoelectric microgripper using improved PI hysteresis model
[J].Journal of Ningbo University(Natural Science & Engineering Edition),2017,30(6):53-58.DOI:
| Title: | Feedforward control of a piezoelectric microgripper using improved PI hysteresis model |
| 作者: | 蔡永根, 崔玉国*, 赵余杰, 刘尔春, 刘 康, 薛 飞 |
| Author(s): | CAI Yong-gen, CUI Yu-guo*, ZHAO Yu-jie, LIU Er-chun, LIU Kang, XUE Fei |
| 关键词: | 压电微定位平台; PI迟滞建模; 阈值优化; 前馈控制 |
| Keywords: | piezoelectric microgripper; PI hysteresis model; threshold optimization; feedforward control |
| 分类号: | TN304 |
| 文献标识码: | A |
| 摘要: | 为减小压电微定位平台的迟滞误差, 设计前馈控制器对其进行控制. 首先在使所建平台迟滞模型精度达到要求并使各阈值点精度相同的情况下, 对平台迟滞模型的阈值进行优化, 得到满足模型精度要求的最小算子数, 进而建立了平台的PI(Prandtl-Ishilinskii)迟滞模型通过对所建迟滞模型求逆, 设计出平台的前馈控制器; 最后在所设计的前馈控制作用下, 使平台达到5μm理想阶跃值的响应时间为0.01s稳态误差中线的变化范围为0.40~0.50μm 当期望平台输出最大值为17μm变幅值三角波位移时, 实测位移相对于理想位移的误差中线变动范围为1.15~ -0.05μm. 所设计前馈控制器可有效减小压电微定位平台的迟滞误差. |
| Abstract: | In order to reduce the hysteresis error of piezoelectric microgripper displacement, a feedforward controller is designed for controlling purposes. First, the dead-zone operator is introduced to the conventional PI hysteresis model, and the hysteresis model of piezoelectric microgripper is built for non singular symmetric and non convex curve of piezoelectric microgripper hysteresis. Then, through the inverse calculations of the hysteresis model, the feedforward control algorithm for piezoelectric micro-gripper is developed. Finally, the feedforward control of piezoelectric microgripper is tested. The results show that when the displacement of piezoelectric microgripper clamp is in the range of 0-15.2 μm, the center line of the hysteresis error is reduced from -1.35-1.50 μm with no control to -0.95-0.47 μm with the feed forward control. The feedforward controller can significantly reduce the hysteresis error of piezoelectric microgripper and improve the tracking accuracy of the reference input. |
| 参考文献 /References: | [1] MAYRA G S, MONIKA L S, MATTHIAS S, et al. Micro-gripper: A new concept for a monolithic single-cell manipulation device[J]. Sensors and Actuators A (Physical), 2015, 236:130-139. [2] KIM B S, PARK J S, KANG B H, et al. Fabrication and property analysis of a MEMS micro-gripper for robotic micro-manipulation[J]. Robotics and Computer-Integrated Manufacturing, 2012, 28:50-56. [3] 孙媛, 金鑫, 叶鑫, 等. 面向中间尺度零件精密装配的微夹持器[J]. 兵工学报, 2014, 35(12):2079-2086. [4] 裘进浩, 陈海荣, 陈远晟, 等. 压电驱动器的非对称迟滞模型[J]. 纳米技术与精密工程, 2012, 10(3):190-197. [5] TANG H, LI Y G. Feedforward nonlinear PID control of a novel micromanipulator using Preisach hysteresis compensator[J]. Robotics and Computer-Integrated Manufacturing, 2015, 34:124-132. [6] 李黎, 刘向东, 王伟, 等. 压电陶瓷执行器迟滞特性的广义非线性Preisach模型及其数值实现[J]. 光学精密工程, 2007, 15(5):701-711. [7] STEFANSKI F, MINOROWICZ B, PERSSON J, et al. Non-linear control of a hydraulic piezo-valve[J]. Systems and Signal Processing, 2017, 82:412-431. [8] 王俐, 饶长辉, 饶学军, 等. 压电陶瓷微动台的复合控制[J]. 光学精密工程, 2012, 20(6):1266-1271. [9] 曾祥进, 黄心汉, 王敏, 等. 基于Dahl 模型的压电陶瓷微夹钳控制研究[J]. 机械工程学报, 2008, 19(7): 766-768. [10] 胡小根, 李玉和, 林浩山, 等. 压电驱动器迟滞建模与开环控制实验研究[J]. 压电与声光, 2010, 32(6):1000- 1001. [11] 唐强, 吉方, 陈东生, 等. 压电陶瓷执行器的动态迟滞建模与零相差前馈补偿控制[J]. 组合机床与自动化加工技术, 2015(9):95-98. [12] ORSZULIKA R R, SHAN J J. Output feedback integral control of piezoelectric actuators considering hysteresis[J]. Precision Engineering, 2017, 47:90-96. |
| 备注/Memo: | 收稿日期: 2017?03?02. 宁波大学学报（理工版）网址: http://journallg.nbu.edu.cn/ 基金项目: 国家自然科学基金（51675288）. 第一作者: 蔡永根（1990－）, 男, 河南商丘人, 在读硕士研究生, 主要研究方向: 微/纳米定位技术. E-mail: 1084653515@qq.com *通信作者: 崔玉国（1971－）, 男, 吉林农安人, 教授, 主要研究方向: 微/纳米定位技术及精密测量技术. E-mail: cuiyuguo@nbu.edu.cn 宁波大学学报（理工版）网址：http://journallg.nbu.edu.cn/ |
