非对称异形截面环件的冷辗扩成形力能参数与圆度影响规律研究
PDF下载 (731)徐焕磊,孙宝寿,袁佳耀,徐永铭,徐振威.非对称异形截面环件的冷辗扩成形力能参数与圆度影响规律研究[J].宁波大学学报(理工版),2021,34(2):61-67.DOI:
XU Huanlei,SUN Baoshou,YUAN Jiayao,XU Yongming,XU Zhenwei.The impact of force parameters on roundness of cold ring rolling of asymmetric abnormal cross-section ring[J].Journal of Ningbo University(Natural Science & Engineering Edition),2021,34(2):61-67.DOI:
| Title: | The impact of force parameters on roundness of cold ring rolling of asymmetric abnormal cross-section ring |
| 作者: | 徐焕磊, 孙宝寿, 袁佳耀, 徐永铭, 徐振威 |
| Author(s): | XU Huanlei, SUN Baoshou, YUAN Jiayao, XU Yongming, XU Zhenwei |
| 关键词: | 冷辗扩; 非对称异形截面环件; 高压油管连接套筒; 轧制力; 轧制力矩; 圆度误差 |
| Keywords: | cold ring rolling; asymmetric abnormal cross-section ring; high pressure oil pipe connecting sleeve; rolling force; rolling torque; roundness error |
| 分类号: | TG335 |
| 文献标识码: | A |
| 摘要: | 以非对称异形截面环件高压油管连接套筒为研究对象, 采用对称冷辗扩工艺, 应用Simufact软件对冷辗扩成形过程进行了模拟分析, 研究了驱动辊转速和芯辊进给速度对冷辗扩过程中轧制力、轧制力矩和环件圆度误差的影响. 结果表明: 降低芯辊进给速度或增大驱动辊转速, 能有效降低两道次冷辗扩过程中的轧制力和轧制力矩; 驱动辊转速为12 rad●s-1, 芯辊进给速度为1.0 mm●s-1时, 第一道次冷辗扩定位凹槽(缩口)内外圈圆度质量最优, 圆度误差分别为0.1735 mm和0.1864 mm; 驱动辊转速为14 rad●s-1, 芯辊进给速度为1.2 mm●s-1时, 第二道次冷辗扩缩口内外圈圆度质量最优, 圆度误差分别为0.0849 mm和0.1202 mm. |
| Abstract: | The process of high-pressure oil pipe connecting sleeve of asymmetric abnormal cross-section ring is studied in this paper. The symmetrical cold ring rolling technology is adopted, and the cold ring rolling process is simulated and analyzed by Simufact software. The effects of driving roller’s rotation speed and mandrel feed speed on the rolling force, rolling torque and ring roundness error in cold ring rolling process of connecting sleeve are explored. The results show that the rolling force and rolling torque can be effectively reduced by decreasing the mandrel feed speed or increasing the driving roller’s rotation speed. When the driving roller’s rotation speed is 12 rad●s-1 and the mandrel feed speed is 1.0 mm●s-1, the first pass cold rolling has the best roundness quality of inner and outer rings of the cold rolling locating groove (shrink mouth) and the roundness errors are 0.1735 mm and 0.1864 mm respectively. When the driving roller’s rotation speed is 14 rad●s-1 and the mandrel feed speed is 1.2 mm●s-1, the second pass cold rolling has the best roundness quality of inner and outer rings of the cold rolling shrink mouth and the roundness errors are 0.0849 mm and 0.1202 mm respectively. |
| 参考文献 /References: | [1] 左治江, 华林. 环件冷辗扩技术现状和发展[J]. 锻压技术, 2005, 30(4):101-106. [2] 何杰, 束学道, 彭文飞, 等. 高铁轴承外圈的冷辗扩变形机理研究[J]. 热加工工艺, 2014, 43(21):101-103. [3] 冯耿, 孙宝寿, 束学道. 冷辗扩高铁轴承内圈工艺参数优化研究[J]. 热加工工艺, 2016, 45(23):128-131. [4] 赵哲骐, 孙宝寿, 束学道, 等. 基于正交试验的高铁轴承内圈冷辗扩壁厚均匀性优化分析[J]. 宁波大学学报(理工版), 2017, 30(4):6-10. [5] 华林, 左治江, 兰箭, 等. 环件冷辗扩芯辊进给速度规范设计[J]. 中国机械工程, 2006, 17(9):953-957. [6] 华林, 潘利波, 李超. 环件径轴向轧制的咬入条件分析[J]. 塑性工程学报, 2007, 14(5):102-105. [7] Li L Y, Yang H, Guo L G, et al. Research on interactive influences of parameters on T-shaped cold ring rolling by 3D-FE numerical simulation[J]. Journal of Mechanical Science and Technology, 2007, 21(10):1541-1547. [8] Guo L G, Yang H. Effect of sizes of forming rolls on cold ring rolling by 3D-FE numerical simulation[J]. Transactions of Nonferrous Metals Society of China, 2006, 16:s645-s651. [9] Yang H, Guo L G, Zhan M, et al. Research on the influence of material properties on cold ring rolling processes by 3D-FE numerical simulation[J]. Journal of Materials Processing Technology, 2006, 177(1/2/3):634- 638. [10] 孙宝寿, 赵哲骐, 徐京豫, 等. 高铁轴承内圈冷辗扩成形的数值模拟和试验研究[J]. 塑性工程学报, 2017, 24(4):6-10. [11] 李华, 王斌, 曹铁珍. 环件宽径比对环件冷辗扩工艺的影响规律研究[J]. 机械设计与制造, 2008(8):144-146. [12] 杨合, 李兰云, 王敏, 等. 异形环件冷辗扩中环件半径扩大变形行为研究[J]. 中国科学(技术科学), 2010, 40(7):802-810. [13] 郭良刚, 杨合, 吴跃江, 等. 材料参数对环件冷辗扩工艺的影响规律研究[J]. 机械科学与技术, 2005, 24(7):839-843; 882. [14] Ryttberg K, Knutson Wedel M, Recina V, et al. The effect of cold ring rolling on the evolution of microstructure and texture in 100Cr6 steel[J]. Materials Science and Engineering: A, 2010, 527(9):2431-2436. [15] 李兰云, 杨合, 郭良刚, 等. 芯辊进给速度对环件冷轧工艺的影响规律[J]. 机械科学与技术, 2005, 24(7):808-811. [16] 方沁林. 圆度误差评定的算法研究与软件设计[D]. 武汉: 华中科技大学, 2007. |
| 备注/Memo: | 收稿日期: 2020－10－19. 宁波大学学报（理工版）网址: http://journallg.nbu.edu.cn/ 基金项目: 国家自然科学基金（51975301）; 浙江省自然科学基金重点资助项目（LZ17E050001）; 宁波市2020年度“科技创新2025”重大专项（2020Z110）. 第一作者: 徐焕磊（1996－）, 男, 浙江宁波人, 在读硕士研究生, 主要研究方向: 塑性成形工艺与装备. E-mail: 2550706025@qq.com *通信作者: 孙宝寿（1960－）, 男, 江苏泰兴人, 副教授, 主要研究方向: 塑性成形工艺与装备. E-mail: sunbaoshou@nbu.edu.cn 宁波大学学报（理工版）网址：http://journallg.nbu.edu.cn/ |
