油润滑状态下颗粒尺寸对PTFE/316L密封界面摩擦学行为的影响
PDF下载 (289)沈明学,李 波,李圣鑫,赵火平,熊光耀.油润滑状态下颗粒尺寸对PTFE/316L密封界面摩擦学行为的影响[J].宁波大学学报(理工版),2021,34(6):17-27.DOI:
SHEN Mingxue,LI Bo,LI Shengxin,ZHAO Huoping,XIONG Guangyao.Effect of particle size on the tribological behavior of PTFE/316L sealing interface under oil-lubricated conditions[J].Journal of Ningbo University(Natural Science & Engineering Edition),2021,34(6):17-27.DOI:
| Title: | Effect of particle size on the tribological behavior of PTFE/316L sealing interface under oil-lubricated conditions |
| 作者: | 沈明学, 李 波, 李圣鑫, 赵火平, 熊光耀 |
| Author(s): | SHEN Mingxue, LI Bo, LI Shengxin, ZHAO Huoping, XIONG Guangyao |
| 关键词: | 橡塑密封; 摩擦界面; 润滑状态; 颗粒尺寸; 磨粒磨损 |
| Keywords: | rubber and plastic seals; friction interface; lubrication state; particle size; abrasive wear |
| 分类号: | TB34 |
| 文献标识码: | A |
| 摘要: | 磨粒磨损是许多流体机械中橡塑密封件常见的失效形式, 外部入侵的污染物或内部衍生的磨粒往往突破材料的耐磨强韧极限. 本文开展了聚四氟乙烯(PTFE)/316L不锈钢摩擦副在油润滑工况下的磨粒磨损实验. 评价了颗粒尺寸作用下密封副的摩擦学性能和磨损机制. 结果表明 除纯油润滑状态外, 摩擦系数与316L磨痕表面损伤程度与颗粒尺寸呈现负相关, 颗粒临界尺寸前后的颗粒运行行为和损伤机制差异显著. 在颗粒临界尺寸之上时, 完整的颗粒仅钉扎入PTFE磨痕边缘而未能穿越密封界面, 部分被碾碎的颗粒可进入接触区域中心; 随着颗粒尺寸的减小, 单个嵌入颗粒演变为堆积性“颗粒群”, 表现出明显的“砂轮效应”; 在颗粒临界尺寸之下时, 颗粒粒度小于润滑油膜厚度, 摩擦副维持流体动力润滑状态, 摩擦系数较小. 密封界面内的磨粒流不断冲蚀配副金属, 形成特殊的“PTFE-颗粒-316L”三体滚动磨损. |
| Abstract: | Abrasive wear is the main failure mode of the rubber and plastic seals in the fluid machinery. Invading contaminants and derived abrasives often break through the wear resistance and toughness limits of sealing materials. This study developed an experiment of the abrasive wear test of the PTFE cylindrical pin and 316L stainless steel disc under oil-lubricated conditions. Tribological properties and wear mechanisms of sealing pairs under the action of particle size were evaluated. The result demonstrated that the friction coefficient was negatively correlated with the wear level of 316L worn surface and particle size except for pure oil-lubricated condition. Particle running behaviour and damage mechanism below and above the particle critical size were significantly different. When the particle size was greater than critical size, only a few crushed particles could enter the centre of wear scar, with many original particles being pinned into the edge of PTFE surface instead of passing through the sealing interface. With the decrease of particle size, a single embedded particle evolved into the stacked “particle group”, and the “grinding wheel effect” from particle running behaviour had a noticeable deterioration. The particle size was smaller than the thickness of the oil film between the tribo-interface when the abrasive size was below the critical threshold. , the hydrodynamic lubrication state between the tribo-interface also held for this contacting condition, and the friction coefficient was small. Abrasive-flow invading in the sealing interface kept on eroding the metallic counterpart surface, as a result the unique “PTFE-particle-316L” three-body rolling wear was formed. |
| 参考文献 /References: | [1] Kurdi A, Kan W H, Chang L. Tribological behaviour of high performance polymers and polymer composites at elevated temperature[J]. Tribology International, 2019, 130:94-105. [2] Zhao F Y, Zhang L G, Li G T, et al. Significantly enhancing tribological performance of epoxy by filling with ionic liquid functionalized graphene oxide[J]. Carbon, 2018, 136:309-319. [3] Harris K L, Pitenis A A, Sawyer W G, et al. PTFE tribology and the role of mechanochemistry in the development of protective surface films[J]. Macro- molecules, 2015, 48(11):3739-3745. [4] Ye J, Khare H S, Burris D L. Transfer film evolution and its role in promoting ultra-low wear of a PTFE nanocomposite[J]. Wear, 2013, 297(1/2):1095-1102. [5] 王枫, 孙小波, 王子君. 轴承保持架用聚四氟乙烯改性材料研究进展[J]. 轴承, 2013(4):59-63. [6] Donnet C, Erdemir A. Solid lubricant coatings: Recent developments and future trends[J]. Tribology Letters, 2004, 17(3):389-397. [7] Lv M, Wang C, Wang Q H, et al. Highly stable tribological performance and hydrophobicity of porous polyimide material filled with lubricants in a simulated space environment[J]. RSC Advances, 2015, 5(66): 53543-53549. [8] Xiang D H, Shan K L. Friction and wear behavior of self-lubricating and heavily loaded metal-PTFE composites[J]. Wear, 2006, 260(9/10):1112-1118. [9] Amrishraj D, Senthilvelan T. Dry sliding wear behavior of ABS composites reinforced with nano zirconia and PTFE[J]. Materials Today: Proceedings, 2018, 5(2): 7068-7077. [10] Riedo E, Gnecco E, Bennewitz R, et al. Interaction potential and hopping dynamics governing sliding friction[J]. Physical Review Letters, 2003, 91(8):084502. [11] Dias R A, Coura P Z, Costa B V. Velocity, temperature, and normal force dependence on friction: An analytical and molecular dynamics study[J]. Physica Status Solidi, 2010, 247(1):98-103. [12] Riedo E, Lévy F, Brune H. Kinetics of capillary condensation in nanoscopic sliding friction[J]. Physical Review Letters, 2002, 88(18):185505. [13] Chen J Y, Ratera I, Park J Y, et al. Velocity dependence of friction and hydrogen bonding effects[J]. Physical Review Letters, 2006, 96(23):236102. [14] Li Q Y, Dong Y L, Perez D, et al. Speed dependence of atomic stick-slip friction in optimally matched experiments and molecular dynamics simulations[J]. Physical Review Letters, 2011, 106(12):126101. [15] Tambe N S, Bhushan B. Nanoscale friction mapping[J]. Applied Physics Letters, 2005, 86(19):193102. [16] Dieterich J H, Kilgore B D. Direct observation of frictional contacts: New insights for state-dependent properties[J]. Pure and Applied Geophysics, 1994, 143(1/2/3):283-302. [17] Evstigneev R M. Nonmonotonic velocity dependence of atomic friction[J]. Physical Review Letters, 2004, 93(23): 230802. [18] Corwin A D, de Boer M P. Effect of adhesion on dynamic and static friction in surface micromachining[J]. Applied Physics Letters, 2004, 84(13):2451-2453. [19] Gotsmann B, Lantz M A. Atomistic wear in a single asperity sliding contact[J]. Physical Review Letters, 2008, 101(12):125501. [20] Lessel M, Loskill P, Hausen F, et al. Impact of van der Waals interactions on single asperity friction[J]. Physical Review Letters, 2013, 111(3):035502. [21] Holmberg K, Kivikyt?-Reponen P, H?rkisaari P, et al. Global energy consumption due to friction and wear in the mining industry[J]. Tribology International, 2017, 115: 116-139. [22] Karl-Heinz Z G. Microstructure and wear of materials[J]. Tribology Series, 1987, 10:554-560. [23] de Pellegrin D V, Torrance A A, Haran E. Wear mechanisms and scale effects in two-body abrasion[J]. Wear, 2009, 266(1/2):13-20. [24] Coronado J J. Abrasive size effect on friction coefficient of AISI 1045 steel and 6061-T6 aluminium alloy in two-body abrasive wear[J]. Tribology Letters, 2015, 60(3):1-6. [25] Shen M X, Dong F, Zhang Z X, et al. Effect of abrasive size on friction and wear characteristics of nitrile butadiene rubber (NBR) in two-body abrasion[J]. Tribology International, 2016, 103:1-11. [26] Stachowiak G B, Stachowiak G W, Brandt J M. Ball- cratering abrasion tests with large abrasive particles[J]. Tribology International, 2006, 39(1):1-11. [27] Zhang S W. Investigation of physical process of polymer abrasive erosion[J]. Tribology, 1993, 2:11-18. [28] Petrica M, Katsich C, Badisch E, et al. Study of abrasive wear phenomena in dry and slurry 3-body conditions[J]. Tribology International, 2013, 64:196-203. [29] Persson B N J, Tartaglino U, Albohr O, et al. Rubber friction on wet and dry road surfaces: The sealing effect[J]. Physical Review B, 2005, 71(3):035428. [30] Heshmat H. Wear reduction systems for coal-fueled diesel engines I. The basics of powder lubrication[J]. Wear, 1993, 162/163/164:508-517. [31] 王文东, 张超, 杜鸣杰, 等. 水/油润滑条件下PTFE复合材料的摩擦学性能[J]. 理化检验(物理分册), 2016, 52(10):717-721. [32] Lan P X, Polycarpou A A. Stribeck performance of drilling fluids for oil and gas drilling at elevated temperatures[J]. Tribology International, 2020, 151: 106502. [33] Chittenden R J, Dowson D, Dunn J F, et al. A theoretical analysis of the isothermal elastohydrodynamic lubrication of concentrated contacts I. Direction of lubricant entrainment coincident with the major axis of the Hertzian contact ellipse[J]. Proceedings of the Royal Society of London A Mathematical and Physical Sciences, 1985, 397:245-269. [34] Hamrock B J, Dowson D. Elastohydrodynamic lubrication of elliptical contacts for materials of low elastic modulus I—Fully flooded conjunction[J]. Journal of Lubrication Technology, 1978, 100(2):236-245. [35] 刘晓玲, 王召岩, 杜肖, 等. 聚氨酯和聚四氟乙烯摩擦磨损性能试验研究[J]. 润滑与密封, 2015, 40(10):15- 18. [36] Qiu M, Yang Z P, Lu J J, et al. Influence of step load on tribological properties of self-lubricating radial spherical plain bearings with PTFE fabric liner[J]. Tribology International, 2017, 113:344-353. [37] Shen M X, Li B, Ji D H, et al. Effect of contact stress on the tribology behaviors of PTFE/316L seal pairs under various abrasive-contained conditions[J]. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 2021, 235(3):639-652. [38] Shen M X, Li B, Ji D H, et al. Effect of particle size on tribological properties of rubber/steel seal pairs under contaminated water lubrication conditions[J]. Tribology Letters, 2020, 68(1):1-15. [39] Habib K A, Cano D L, Heredia J A, et al. Analysis of the hardness ratio effect on the tribological performance of NiCrBSi coating/debris particles using the Stribeck curve[J]. Wear, 2021, 486/487:204081. [40] Shen M X, Li B, Li S X, et al. Effect of particle concentration on the tribological properties of NBR sealing pairs under contaminated water lubrication conditions[J]. Wear, 2020, 456/457:203381. [41] Salonitis K, Chondros T, Chryssolouris G. Grinding wheel effect in the grind-hardening process[J]. The International Journal of Advanced Manufacturing Technology, 2008, 38(1/2):48-58. [42] Zhao Y W, Chang L. A micro-contact and wear model for chemical-mechanical polishing of silicon wafers[J]. Wear, 2002, 252(3/4):220-226. [43] Xiao H P, Sinyukov A M, He X L, et al. Silicon-oxide- assisted wear of a diamond-containing composite[J]. Journal of Applied Physics, 2013, 114(22):13-17. |
| 备注/Memo: | 收稿日期:2021-09-03.宁波大学学报（理工版）网址:http://journallg.nbu.edu.cn/ 基金项目:国家自然科学基金（51775503,51805170）;江西省杰出青年基金（20212ACB214003）;江西省自然科学基金（20192BAB206026）. 第一作者:沈明学（1982－）,男,浙江嘉兴人,博士/教授,主要研究方向:橡塑、轮轨摩擦学及表面工程技术.E-mail:shenmingxue@126.com *通信作者:熊光耀（1962－）,男,江西南昌人,教授,主要研究方向:增材制造、材料表面改性与防护.E-mail:xiongguangyao@163.com 宁波大学学报（理工版）网址：http://journallg.nbu.edu.cn/ |
