激光能量密度对CoCrFeNiMo高熵合金组织与耐磨性能的影响
PDF下载 (163)韩 波,贺华波.激光能量密度对CoCrFeNiMo高熵合金组织与耐磨性能的影响[J].宁波大学学报(理工版),2024,37(1):112-120.DOI:10.20098/j.cnki.1001-5132.2023.0919
HAN Bo,HE Huabo.Influence of laser energy density on the microstructure and wear resistance of CoCrFeNiMo high-entropy alloy[J].Journal of Ningbo University(Natural Science & Engineering Edition),2024,37(1):112-120.DOI:10.20098/j.cnki.1001-5132.2023.0919
| Title: | Influence of laser energy density on the microstructure and wear resistance of CoCrFeNiMo high-entropy alloy |
| 作者: | 韩 波, 贺华波 |
| Author(s): | HAN Bo, HE Huabo |
| 关键词: | 激光熔覆; 高熵合金; 激光能量密度; 耐磨性; 磨损机制 |
| Keywords: | laser cladding; high-entropy alloy; laser energy density; wear resistance; wear mechanism |
| 分类号: | TG178 |
| DOI: | 10.20098/j.cnki.1001-5132.2023.0919 |
| 文献标识码: | A |
| 摘要: | 通过激光熔覆制备不同激光能量密度下的CoCrFeNiMo高熵合金涂层, 研究了不同激光能量密度对涂层微观组织、显微硬度和摩擦学性能的影响. 研究结果表明, 所有CoCrFeNiMo高熵合金涂层的相都由FCC和σ相组成, 具为典型枝晶组织, 枝晶区和枝晶间区组成分别是FCC相和σ相. 随着激光能量密度的升高, 涂层显微硬度先升高后下降, 和耐磨性成正相关. 当激光能量密度为66.7J/mm2时, 涂层显微硬度达到419.8HV的最高值, 耐磨性最好, 其原因是较高硬度提高了涂层抗变形能力, 有效抵抗了摩擦副对涂层的磨损. 由此可见, 高熵合金涂层磨损机制由磨粒磨损、黏着磨损和氧化磨损共同作用形成. |
| Abstract: | In this study, CoCrFeNiMo high-entropy alloy coatings were prepared using laser cladding technique under different laser energy densities. The influence of different laser energy densities on microstructure, microhardness, and tribological properties were investigated. The results showed that all CoCrFeNiMo high-entropy alloy coatings consisted of FCC and σ phases, exhibiting a typical dendritic microstructure, where the dendritic regions and inter-dendritic regions were composed of FCC and σ phases, respectively. With the increase in laser energy density, microhardness of the coatings initially increased and then decreased, showing a positive correlation with wear resistance. When the laser energy density was 66.7J/mm2, the microhardness of the coating reached its highest value at 419.8HV, indicating the best wear resistance. It is because that the higher hardness of the coating leads to better deformation resistance, and thus effectively resists the wear caused by frictional forces. The wear mechanism of the high-entropy alloy coatings involved a combination of abrasive wear, adhesive wear, and oxidative wear. |
| 参考文献 /References: | [1] 李建国, 黄瑞瑞, 张倩, 等. 高熵合金的力学性能及变形行为研究进展[J]. 力学学报, 2020, 52(2):333-359. [2] 马旻昱, 连勇, 张津. 增材制造技术制备高熵合金的研究现状及展望[J]. 材料导报, 2020, 34(17):17082-17088. [3] JIN G, CAI Z B, GUAN Y J, et al. High temperature wear performance of laser-cladded FeNiCoAlCu high-entropy alloy coating[J]. Applied Surface Science, 2018, 445:113-122. [4] FU Y, HUANG C, DU C, et al. Evolution in microstructure, wear, corrosion, and tribocorrosion behavior of Mo-containing high-entropy alloy coatings fabricated by laser cladding[J]. Corrosion Science, 2021, 191:109727. [5] ZHANG M N, WANG D F, HE L J, et al. Microstructure and elevated temperature wear behavior of laser-cladded AlCrFeMnNi high-entropy alloy coating[J]. Optics & Laser Technology, 2022, 149:107845. [6] ARIF Z U, KHALID M Y, UR REHMAN E, et al. A review on laser cladding of high-entropy alloys, their recent trends and potential applications[J]. Journal of Manufacturing Processes, 2021, 68:225-273. [7] ZHANG P, LI Z, LIU H, et al. Recent progress on the microstructure and properties of high entropy alloy coatings prepared by laser processing technology: a review[J]. Journal of Manufacturing Processes, 2022, 76:397-411. [8] 刘昊, 高强, 郜文鹏, 等. 激光熔覆CoCrFeNiNbx高熵合金涂层的高温摩擦磨损性能[J]. 摩擦学学报, 2022, 42(5):966-977. [9] 陈国进, 张冲, 唐群华, 等. 含B量对激光熔覆FeCoCrNiBx (x=0.5, 0.75, 1.0, 1.25)高熵合金涂层组织结构与耐磨性的影响[J]. 稀有金属材料与工程, 2015, 44(6):1418-1422. [10] LIU H, GAO Q, DAI J B, et al. Microstructure and high-temperature wear behavior of CoCrFeNiWx high-entropy alloy coatings fabricated by laser cladding[J]. Tribology International, 2022, 172:107574. [11] YANG Y C, REN Y J, TIAN Y W, et al. Microstructure and tribological behaviors of FeCoCrNiMoSix high-entropy alloy coatings prepared by laser cladding[J]. Surface and Coatings Technology, 2022, 432:128009. [12] 姜明明, 孙树峰, 王津, 等. 激光熔覆制备高熵合金涂层耐磨性研究进展[J]. 材料工程, 2022, 50(3):18-32. [13] 周子钧, 姜芙林, 杨发展, 等. FeCoNiCrNb0.5Mo0.25高熵合金激光熔覆层组织的共晶化行为及耐磨耐蚀机理[J]. 中国激光, 2023, 50(4):110-125. [14] REN Y J, LIANG L X, SHAN Q, et al. Effect of volumetric energy density on microstructure and tribological properties of FeCoNiCuAl high-entropy alloy produced by laser powder bed fusion[J]. Virtual and Physical Prototyping, 2020, 15(Suppl.1):543-554. [15] ZHANG Y, HAN T, XIAO M, et al. Effect of process parameters on the microstructure and properties of laser-clad FeNiCoCrTi0.5 high-entropy alloy coating[J]. International Journal of Minerals, Metallurgy and Materials, 2020, 27(5):630-639. [16] 聂金浩, 杨宜鑫, 李玉新, 等. 激光能量密度对激光熔覆NiCoCrAlY涂层组织与性能的影响[J]. 兵工学报, 2021, 42(5):1083-1091. [17] LIU Y, XIE Y X, CUI S G, et al. Effect of Mo element on the mechanical properties and tribological responses of CoCrFeNiMox high-entropy alloys[J]. Metals, 2021, 11(3):486. [18] ZHOU C, WANG S R, WANG G Q, et al. Investigation on the microstructure, wear and corrosion resistance of FeCoNiCrMox high-entropy alloy coatings deposited on 40Cr by laser cladding[J]. Journal of Materials Science, 2022, 57(39):18615-18639. [19] DUAN X, WANG S R, WANG G Q, et al. Microstructure evolution and frictional wear behavior of laser cladding FeCrCoNiMo0.5Wx high-entropy alloy coatings[J]. Intermetallics, 2023, 158:107888. [20] YIN T Y, ZHANG S, WANG Z Y, et al. Effect of laser energy density on microstructural evolution and wear resistance of modified aluminum bronze coatings fabricated by laser cladding[J]. Materials Chemistry and Physics, 2022, 285:126191. [21] CUI C, WU M P, MIAO X J, et al. The effect of laser energy density on the geometric characteristics, microstructure and corrosion resistance of Co-based coatings by laser cladding[J]. Journal of Materials Research and Technology, 2021, 15:2405-2418. [22] ZHANG H, PAN Y, ZHANG Y, et al. Effect of laser energy density on microstructure, wear resistance, and fracture toughness of laser cladded Mo2FeB2 coating[J]. Ceramics International, 2022, 48(19):28163-28173. [23] 王石, 王琳, 尹晓伟. 激光熔覆FeCoCrNiNb高熵合金涂层组织及耐磨性能[J]. 稀有金属材料与工程, 2023, 52(4):1483-1489. [24] LI X F, FENG Y H, LIU B, et al. Influence of NbC particles on microstructure and mechanical properties of AlCoCrFeNi high-entropy alloy coatings prepared by laser cladding[J]. Journal of Alloys and Compounds, 2019, 788:485-494. [25] MOUSAVI S E, HE A Q, PALIMI M, et al. Influences of alloying elements on microstructure and tribological properties of a medium-weight high-entropy alloy[J]. Wear, 2023, 524/525:204856. |
| 备注/Memo: | 收稿日期: 2023－09－26. 宁波大学学报（理工版）网址: http://journallg.nbu.edu.cn/ 基金项目: 宁波市“科技创新2025”重大专项（2022Z015）. 第一作者: 韩波, 硕士研究生, 主要研究方向: 激光增材制造. E-mail: 2359309704@qq.com *通信作者: 贺华波, 博士/副教授, 主要研究方向: 机械设计与理论. E-mail: hehuabo@nbu.edu.cn 宁波大学学报（理工版）网址：http://journallg.nbu.edu.cn/ |
